Procom PCSD25T Guida di Installazione

VENT-FREE GAS STOVE MODEL # PCSD25T PCSD25RT – Do not store or use gasoline or other flammable vapors and

10 INSTALLATION NOTICE: This heater is intended for use as supplemental heat. Use this heater along with your primary heating system. Do not inst

11 CONNECTING TO GAS SUPPLY WARNING: A qualified technician must connect heater to gas supply. Follow all local codes. WARNING: This appliance

12 CAUTION: Use only new black iron or steel pipe. Internally tinned copper tubing may be used in certain areas. Check your local codes. Use pipe o

13 For changing from natural gas supply to propane supply 1. Remove bottom screw from cover plate, see figure 8, and rotate to expose fuel selectio

14 CHECKING GAS CONNECTIONS WARNING: Test all gas piping and connections for leaks after installing or servicing. Correct all leaks immediately.

15 WARNING: Failure to position the parts in accordance with these diagrams or failure to use only parts included may result in property damage

16 Figure 14 Figure 15 Installation for Remote Receiver: The remote receiver operates on four AA-siz

17 OPERATION FOR YOUR SAFETY READ BEFORE LIGHTING WARNING: If you do not follow these instructions exactly, a fire or explosion may result

18 LIGHTING INSTRUCTIONS For PCSD25T Unscrew ignitor cap and install a AAA battery with the + pointing out. Replace cap. 1. STOP! Read t

19 TO TURN OFF GAS TO APPLIANCE Shut off heater Turn Control Knob clockwise to the OFF position. Do not force. MANUAL LIGHT

2 TABLE OF CONTENTS Important Safety Information ...

20 LIGHTING INSTRUCTIONS For PCSD25RT 1. STOP! Read the safety information on the front and back of the warning plate o

21 REMOTE CONTROL FOR PCSD25RT MATCHING SECURITY CODES When matching security codes, be sure slide button on the receiver is in the REMOTE

22 OFF OPERATION Press the OFF key and the appliance flame will shut off. During this time the LCD screen will show OF (figure 23). After 3 second

23 INSPECTING BURNERS Check pilot flame pattern and burner flame patterns often. PILOT FLAME PATTERN 1. Turn control knob to pilot position 2. I

24 CARE AND MAINTENANCE WARNING: Failure to keep primary air openings of burners clean may result in sooting and property damage. CAUTION: You

25 TROUBLESHOOTING WARNING: If you smell gas  Shut off gas supply.  Do not try to light any appliance.  Do not touch any electrical switc

26 OBSERVED PROBLEM PROBABLE CAUSE REMEDY ODS/pilot lights but flame go

27 OBSERVED PROBLEM PROBABLE CAUSE REMEDY Slight smoke or odor during initial operat

28 REPLACEMENT PARTS NOTE: Use only original replacement parts. This will protect your warranty coverage for parts replaced under warranty. PARTS

29 PARTS LIST This list contains replaceable parts used in your heater. When ordering parts, follow the instructions listed under Replacement Parts

3 IMPORTANT SAFETY INFORMATION IMPORTANT: Read this owner’s manual carefully and completely before trying to assemble, operate, or service this he

30

31 WARRANTY INFORMATION Keep This Warranty IMPORTANT: We urge you to fill your warranty registration card within TEN (10) days of date of installa

4 7. Always run heater with control knob at PILOT/IGN, LOW or HIGH (5-1) for model PCSD25T locked positions. Never set control knob between locked

5 PRODUCT FEATURES SAFETY PILOT This heater has a pilot with an Oxygen Depletion Sensing (ODS) safety shutoff system. ODS/pilot shuts off the heat

6 UNPACKING 1. Remove top

7 AIR FOR COMBUSTION AND VENTILATION WARNING: If the area in which the heater may be operated does not meet the required volume for indoor comb

8 DETERMINING FRESH-AIR FLOW FOR HEATER LOCATION Determining if You Have a Confined or Unconfined Space Use this worksheet to determine if you ha

9 Ventilation Air from Inside Building This fresh air would come from adjoining unconfined space. When ventilating to an adjoining unconfined s